TC4钛合金厚板电偶腐蚀与防护研究

目的研究TC4钛合金厚板与铝合金、钢之间发生电偶腐蚀的敏感性。方法通过测定TC4钛合金厚板与铝合金、钢组成的电偶对的电偶电流方法,研究TC4钛合金厚板与上述异种材料之间发生电偶腐蚀的敏感性。结果 TC4钛合金厚板与铝合金、钢接触时极易发生电偶腐蚀,不能直接接触使用,必须采取有效的防护措施。对钛合金和铝合金进行阳极氧化处理,可降低电偶腐蚀敏感性;对钛合金进行阳极氧化处理,同时对钢进行电镀镉-钛处理可以在一定程度上降低电偶腐蚀敏感性。结论 TC4钛合金厚板与铝合金及钢的电偶腐蚀敏感性高,表面处理可以有效降低异种材料的电偶腐蚀敏感性。     

铝合金微动疲劳研究及展望

微动疲劳广泛存在于航空航天等各种机械构件中,加速构件接触表面及表层裂纹的萌生与扩展,微动是导致构件多裂纹损伤的主要原因之一。由于海军飞机服役环境的复杂性,铝合金构件腐蚀相当严重,腐蚀对航空铝合金材料微动疲劳的影响是研究微动疲劳时要考虑的重要因素。总结了国内外铝合金微动疲劳研究现状,阐述了研究存在的主要问题,对飞机构件铝合金材料微动疲劳的研究进行了展望。     

机场环境下飞机LY12CZ结构腐蚀损伤预测方法研究

依据LY1 2CZ材料的EXCO溶液浸泡加速腐蚀试验数据、飞机LY 12CZ构件在机场环境下的真实腐蚀损伤数据以及腐蚀损伤等效原则和当量关系原理,获得了该材料在2种环境下腐蚀的当量因子均值(α) =0.023 6,构建了LY12CZ材料于EXCO溶液中浸泡腐蚀的神经网络腐蚀深度预测模型.在此基础上提出了利用所建的神经网...     

双极电化学氧化降解水中苯胺

采用钛基氧化物涂层材料（Ti/SnO2-Sb2O5）为阳极,石墨为阴极,在含Fe2＋和不含Fe2＋2种电解质条件下研究了苯胺的电化学氧化降解效率和机制.结果表明,Ti/SnO2-Sb2O5阳极氧化降解有机物的电位约2.0 V±0.1 V,而石墨阴极还原O2生成H2 O2的优化电位为-0.65 V.H2 O2单独作用不能...     

Effect of two TiO2 nanoparticles on the growth of unicellular green algae using the OECD 201 test guideline: influence of the exposure system

This work aimed at assessing the influence of different exposure systems to perform the commonly used OECD 201 freshwater algal growth inhibition test in the context of nanoparticles hazard assessment. Two distinct TiO₂ nanoparticles were considered and three different exposure systems were investigated: Erlenmeyers flasks and 24-well microplates (both using an orbital shake system), and an alternative system using cylindrical vials and magnetic stirring. All three systems are in accordance with the OECD 201 test guideline recommendations. We concluded that the exposure systems applied to achieve the test can substantially affect the ecotoxicological results and the subsequent calculated ECx. The selected systems influenced both the interaction between algal cells and TiO₂ nanoparticles as well as the growth inhibition recorded. Disparities in ecotoxicity relative to the TiO₂ nanoparticles tested were also observed and are finally discussed.     

Fe掺杂TiO2催化剂制备及其光催化脱汞机理

采用溶胶-凝胶法制备Fe-TiO₂(Fe掺杂纳米二氧化钛)催化剂,通过XRD(X射线衍射仪)、SEM(扫描电镜)、EDX(能量色散X射线光谱仪)和UV-Vis谱对其形态、结构、组成和性质进行表征. 采用Fe-TiO₂催化剂脱除气态Hg0(元素汞),研究了该催化剂在紫外光和可见光下的脱汞效果,并考察了Fe3+的最佳掺杂比. 结果表明:在Fe-TiO₂光催化剂中,TiO₂以锐钛矿相形态存在,当Fe3+掺杂浓度〔以n(Fe)/n(Ti)计〕达到0.010时,所制备的Fe-TiO₂在紫外光和可见光下的脱汞率均达到最大,分别为54.76%和18.92%. 提出了Fe-TiO₂光催化脱汞的可能机制:Fe3+掺入TiO₂结构中,使TiO₂的导带与Fe3+的d轨道发生重叠,导致TiO₂能带变窄,从而扩展了可见光的响应范围;Fe3+在TiO₂中作为一个浅俘获阱,当其俘获光生电子以后,光生空穴能够继续扩散到TiO₂表面发生表面化学反应,生成具有强氧化性的超氧自由基O₂-和·OH,对Hg0进行氧化;当Fe3+掺杂浓度大于0.010时,由于过多的Fe3+成为了光生电子和光生空穴的俘获位,从而使俘获的电子-空穴对通过量子隧道效应复合的概率增加,同时,活性氧化物种O₂-和·OH相互消耗,抑制了光催化效率.      

磁载纳米TiO2复合光催化材料的研究进展

磁载纳米TiO2复合光催化剂是一种无污染,制备成本低,催化活性高,在外加磁场下可迅速分离回收和重复使用的光催化材料,在废水的光催化降解中有着诱人的应用前景.本文综述了不同类型磁载纳米TiO2复合光催化材料的制备方法和光催化性能,总结了其在染料、农药、芳香烃及其衍生物、有害无机离子和有毒气体等各种环境污染物处理中的应用,并展望了磁载纳米TiO2复合光催化剂的发展方向.     

Corrosion behavior of steels for CO2 injection

The process chain for Carbon Capture and Sequestration (CCS) includes tubing for injection of CO₂ into saline aquifers. The compressed CO₂ is likely to contain specific impurities; small concentrations of SO₂ and NO₂ in combination with oxygen and humidity are most harmful. In addition, CO₂ saturated brine is supposed to rise in the well when the injection process is interrupted. The material selection has to ensure that neither CO₂ nor brine or a combination of both will leak out of the inner tubing. In this comprehensive paper the investigated materials range from low-alloy steels and 13% Cr steels up to high-alloy materials. Electrochemical tests as well as long term exposure tests were performed in CO₂, in brine and combination of both; pressure was up to 100 bar, temperature up to 60 °C. Whereas the CO₂ stream itself can be handled using low alloy steels, combinations of CO₂ and brine require more resistant materials to control the strong tendency to pitting corrosion. The corrosion behavior of heat-treated steels depends on factors such as microstructure and carbon content. For different sections of the injection tube, appropriate materials should be used to guarantee safety and consider cost effectiveness.     

二氧化钛颗粒的制备及其脱硫吸附性能

采用溶胶-凝胶法(Sol-gel)在不同烧结温度(340℃,440℃,540℃,640℃)下制备了4种多孔TiO₂颗粒,X射线衍射法(XRD)测得4种样品的晶相均为锐钛矿型.低温77K氮气吸附法计算4种样品的比表面积为79～124m²/g,平均孔径56.8～254.8 A.电子扫描电镜分析了样品的表面结构为多孔高孔隙率结构在固定床中对4种样品进行动态脱硫试验,试验结果表明烧结温度在540℃时制备的样品品质较好,每g TiO₂颗粒可吸附38.9mg的SO₂.以SG 540样品为例,研究了固定床中吸附温度,气相中SO2的浓度以及气体流速对其脱硫吸附性能的影响.与活性炭、沸石物理吸附剂比较,TiO₂颗粒具有较高的脱硫吸附能力.FTIR红外光谱分析法,结合加热脱附试验的结果,得知TiO₂颗粒吸附剂脱硫的机理主要是物理吸附.     

超深井径向钻孔钛合金管转向阻力计算及安全评估

为了解决塔河油田6000 m及以上深井径向钻孔作业时管柱强度低、无法很好地传递钻压等问题,提出利用修井机和油管、钛合金管进行径向钻孔工艺,并通过数值模拟的方法优选有矫直段的单向弯曲转向轨道,研究轨道转向半径、钛合金管外径及壁厚、轨道与管柱间隙对钻进能力的影响,其次,通过正交试验方法,对上述参数进行敏感度分析并进行参数优...